• 10 E. Park Avenue | Kiel, WI 53042-0126
  • 1-800-877-8913

The Trusted Name In

Custom Medical Carts

Certified

ISO 13485: 2016

Certified

ISO 9001: 2015

How Do You Test a Powder-Coated Paint Finish for Medical Carts?

Posted by Greg Binversie on September 11, 2015

Many of the custom medical carts HUI manufactures have a powder-coated finish. As with any finish applied to any product, the powder coating we apply needs to be tested to ensure that the finish is going to last. The following is a brief description of some of the tests we commonly use to validate that our powder-coated finishes are in tolerance, properly cured, and ready to stand up to the usage and environmental conditions your carts will be used in.

Tests for Powder Coat Paint Finishes

Adhesion Tests

Crosshatch – The crosshatch test is designed to test the adhesion of the powder coating to the metal substrate. It’s performed by cutting a crosshatched grid pattern into the coating all the way down to the substrate. A special pressure-sensitive tape is then applied to the crosshatched area and then removed quickly at close to a 180° angle. The area is then inspected to see if any of the coating lifted away from the substrate.

Mandrel Bend – This test checks the elasticity and the adhesion of the powder coating to the substrate. A cured sample panel is placed into a small device that bends the panel over onto itself. The coating should not crack or lose adhesion in the area of the bend.

Impact Test – Similar to the mandrel bend test, the impact test deforms a sample panel in order to test the adhesion of the powder coating. The sample panel is placed into the testing machine where a ball is dropped onto it to produce a deep depression. Here again, the powder-coated finish should not crack or lose adhesion to the substrate in the impact area.

Durability Test

Salt Spray Test – This is a corrosion-resistance test and is performed by scribing a line or “X” into the surface of a finished powder-coated panel. The panel is then placed into a chamber where a corrosive mist is applied to it. The panel is taken out of the chamber at set time intervals and the distance that the coating has “crept” away from the scribed line is measured and recorded. If the amount of creep does not exceed the allowable distance in the pre-determined time intervals, the panel passes the test.

Cure and Finish Tests

MEK Rub Test – This test is used to ensure proper cure of the powder coating to the substrate. Methyl Ethyl Ketone (MEK) is applied to a surface of the part or panel, then rubbed with a cotton swab. The area is observed for degradation or loss of paint adhesion to the substrate.

Color Match – Once our powder-coated parts have cured and cooled off after being in the bake oven, the finished color is compared to an approved color chip sample. This visual inspection is the most common and quickest method to check the color. If there is a variance, the color can then be measured using a photo spectrometer to provide data that can be compared to a known sample and tolerance range for the specific color.

Gloss Measurement – The gloss of a finished powder-coated part is validated by measuring the specular reflection of its surface. This test is performed using a gloss meter, which shines a light onto the surface of the part at a fixed angle, then measures the amount of light reflected off it. If the measurement is out of tolerance, it may be an indication that the powder coating has not cured properly.

Coating Thickness Test

To achieve the best coating performance, each powder has a specified thickness range it must be applied within. HUI takes this measurement at two different stages during the powder-coating process. Our powder room technician uses a dry mil gage to take the first measurement right after the part comes out of the powder booth. The technician can then relay to the painters if they’re applying the correct amount of powder onto the parts. This immediate feedback is beneficial because it catches possible light- or heavy-coated parts before the powder is cured and it’s too late to fix the problem. After the parts have cured, the mil thickness is checked again to verify the coating thickness is within tolerance for the specified powder.

At HUI, we validate our painting processes to ensure that a medical cart’s finish stays beautiful and durable, so that you receive the finish you desire.

If you have questions about powder coating or you’re looking at starting a custom medical cart project, please contact us today!

New Call-to-action

Topics: Medical Cart Design


Share this:

Leave a Reply

Your email address will not be published. Required fields are marked *

Subscribe to Blog

Most Popular Posts